1179 Results
View results:
Sort by:
Torsion Settings for Timber Design According to NDS
What does each option do under the "Calculation of Torsion" section under the Strength Configuration settings?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Result Selection for Design Situation / Result Combination
Why are the maximum deformations not displayed?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Load Extension Isotropic Masonry | Plastic
Is it possible to influence the transverse distribution of a load in the case of the Isotropic | Masonry | Plastic material model?
Option – Independent FE Mesh Preferred
What is the effect of the "Independent FE Mesh Preferred" option in the mesh settings?
Plastic Hinges
How do I define a plastic hinge in RFEM 6?
Advantages of CFD Simulation
What are the advantages of CFD simulation compared to conventional experimental tests?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
Direct vs. Iterative Solver
The calculation in RFEM 6 takes a very long time, but the processor utilization of my system is low. Why is this?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Area Loads on Members via Cells
How can I generate an area load on members via cells in RFEM 6 or RSTAB 9?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Design properties
Where can I specify various properties for the design (for example, effective lengths)?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Incorrect Material or Cross-Section Conversion in Revit or Tekla
I get an incorrect conversion in Tekla/Revit when using regular expressions in the conversion table.
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM